Parkersburg WV Heating, AC Repair & Plumber

High heat

Inducer motor

Helped customer with stuck filter and installed new filter.

Hot water tank

Solenoid in Skuttle humidifier has failed and water supply feed tube is damaged. Customer has declined repair and plans to get a new one when they replace the system in a few years.

19 yr old carrier. Limit Switch was unable to reset when I arrived and system stuck in limit fault. Bypassed switch and tested temp inside heat exchanger cabinet. Temperature never got above 165, switch was rated to open at 190. Also tested combustion analysis and gas pressure. Picked up new switch at supply house and replaced.

Tightened spade connection points on limit switches on floor furnace. Unit fires up every time I turned it on. If issues comes back limit switches will most likely need replaced.

1997 carrier style furnace has a locked up draft motor. Estimate repair cost for motor is $600-900. Furnace is in poor condition, top cabinet is very rusty. I do not recommend repair. Customer is getting an estimate today to replace furnace and possibly hot water tank. Set customer back up in monthly hvac maintenance program, their card had expired in June.

After replacing mount we found blower pulling high amps and shaking pretty badly. Replaced blower motor, capacitor, and wheel.

HVAC Service - P

Replace existing furnace and AC

Customer wished to have old thermostat put back on because of particular scheduling and it matches all the other stats they have.

Gas company shut off furnace and hot water tank, they couldn’t tell what was putting off the high co levels. Old General Electric gas furnace (looks to be 1987)failed combustion analysis. Was reading 562 ppm of carbon monoxide in the flue vent before removing my combustion analysis tool. Left and center chamber are compromised giving off high levels. Furnace has been condemned and red tagged.Hot water tank was installed in 2018 and passed combustion analysis test. Customer is getting an estimate today for a new furnace from 3-5pm.

Filter upgrade, repair duct that is falling apart above furnace, surge protectors, cleaning blower compartment.

Installation of the new blower motor.

HVAC Maintenance - filter sizes are 16-25-1(2), 20-25-1, 20-25-5(2), washable. Found capacitor in attic and on outdoor Lennox system just at allowable spec level. Might need to possibly change parts out in near future but at this time it is within range. Changed all filters and cleaned each system. Send bill for filters.

Quote Only

Replaced burner assembly, flame sensor, and igniter under warranty

Replaced control board and igniter

Gas valve Board

Motor mount for blower motor on York furnace has broken. Unable to find mount in town for motor. Ordered a mount from Virginia air and will return when part arrives.

Drain line for pump goes to roof and is freezing keeping the pump from operating properly. There is no good options for drain other than tearing ceiling out to reroute drain. Russ is checking about getting a team out this afternoon to fix.

Cleaned dirty flame sensor on 12 yr old Philco furnace. Customer hadn’t had heating maintenance done yet so I went ahead and did the heating check today. Combustion analysis, gas pressure, and amp draws are good. Filter is clean. Cleaned flame sensor and drain line. Tightened stat wire connection. Unit ran the first time I fired it up. Now it shuts off a second after ignition. I’ve tried jumping all the pressure switches thinking that may be the issue but system still won’t stay lit. Will need to order a control board for the system. Estimate $600-800 for a new board. Igniter also appears in rough shape, it should be replaced as well.

2009 heil furnace had a pressure switch that failed to open causing system not to run. Replaced switch and system is functioning again.

26 yr old carrier furnace was plugged up with water. When I removed drain hose the water that was in the draft motor came pouring out. Cleaned up water and cleared out clogged drain trap with air. Put unit back together and system is running again. Adjust gas pressure from 3.6 down to 3.3 inwg. Customer is aware of age and condition of her system but wants to wait until the spring before replacing the system.