Parkersburg WV Heating, AC Repair & Plumber

Service Call Platinum Client Arrived to find gas valve had failed. Replaced with new and tested operation. All checks good

Commercial Service Fee - Branch Line Drain Clean. Tried to Snake Through Kitchen Drain that was Backed up. Couldn't Get it. Snaked through Cleanout In the Basement and Got it to go down. Line will need Replaced. Old Galvanized that is built up and causing the blockage. Paid for Furnace/AC/Water Heater and today's work today.

A.O. Smith 50 Gal Natural Gas Hot Water Tank

A.O. Smith 50 Gal Natural Gas Hot Water Tank

Service Call After Hours Fee Furnace had restricted burners. Cleaned them set gas pressures and cleaned flame sensor.

Performed Platinum Comfort Club Membership Tune-Up on Heating System. Performed maintenance on York system with a AA413 filter. All checks good at this time.

#413 Replacement Media for Aprilaire 4400, 2410, & 3410

Performed Platinum Comfort Club Membership Tune-Up on Heating System. Performed maintenance on 19yr old Arcoaire system, uses a Skuttle 20x25x5 filter. Arrived to find run capacitor out of range, customer elected to address that today and it was replaced. Recent service call stated noisy inducer draft motor. The rise in noise appears to be intermittent and although on the higher end, it is still running in range with amperage. System uses R-22 refrigerant and although it is starting to show age, unit is operating properly and safely at this time.

Warranty Part Repair on Furnace.

Service Call Fee: furnace running upon arrival. customer described that system would run on and off, describing what sounded like an overheat or a flame sensing issue. no issue found with heat cycle or gas pressure, clean filter, however the flame sense was quite dirty. cleaned flame sensor and tested operation. furnace is operating properly at this time.

Performed Safety, Health, and Efficiency Inspection.

Service Call Platinum Client: customer informed me that the furnace kicked off and took maybe 2 hours to kick back on. I checked the thermostat and everything checked out good. I then checked the temperature rise of the furnace and it was running 8 degrees over the manufactures recommended heat rise. I replaced the filter and checked the vents. Everything looked good. I adjusted the fan speed to the next fastest setting and this brought my heat rise back within those manufacturers specifications. Everything checks out good at the moment and homeowner will notify if any changes.

Service No Charge: Returned to replace cracked connector as quoted. Removed the bad one and placed the new one on. Verified operation. Everything checks out good.

Performed Platinum Comfort Club Membership Tune-Up on Heating System Furnace is producing high levels of carbon monoxide within combustion. Combustion analyzer was registering 1100 ppm and rising. Checked gas pressures, checked flue. System is unsafe to run and discussed options with customer as far as repair vs replacement. System is 20 years old. Scheduled estimate for replacement for 1/31/22 between 1-3 p.m.

Service Call Platinum Client Arrived to find the system out on high limit. Filter was plugged up and customer had closed some registers to the third level. Opened registers about 50% and changed out filter. Temp rise looked good at 47. All checks good. Customer will need invoice send to her. Customers son was at home but she was in an appointment.

Performed Platinum Comfort Club Membership Tune-Up on Heating System Cleaned and checked operation of equipment. Checked washable filter and installed 16-25-5 filter that customer had. Homeowner was not present at time of maintenance. Recommend surge protection for equipment. Gas furnace: Exhaust amps 1.75 Blower amps 10.32 Gas pressure 3.18 Temp rise 40 degrees O2 10.6 Efficiency 88.3 Tstk 117 degrees CO(0) 67 ppm

Service Call Platinum Client: Arrived to look at gas valve. Problem was gas union.

Service Call Platinum Client- no issues found with furnace. Customer concerned about long run time in the mornings. Customer turns thermostat down to 64 degrees at night and then turns up to 70. I adjusted gas pressure up from 3.2 inwg to 3.7 inwg to help make customer happy with more heating potential. Explained with making the furnace make up 6 degrees difference will take some time with the colder temperatures that we have been having along with also heating the upstairs. They turned upstairs furnace down to 60 degrees at night. The downstairs unit is scheduled to turn on sooner than the upstairs.

Performed Platinum Comfort Club Membership Tune-Up on Heating System