Parkersburg WV Heating, AC Repair & Plumber

Service Call Fee: Diagnosed All Plumbing Issues. Removed and Replaced Laundry Shut Off Valves and Hooked them Back Up. Disconnected Pedistal Sink and Removed it to Install Cabinet and Vanity when we come Back. Replaced Main Shut Off Valve that Leaks when Pressure is on it. Gave Quote to Install Drip Leg and Shut Off Valve on Hot Water Tank. May Need to Come Back and Install Cabinet and Finish Plumbing For Lavatory, Will Still Need Priced when we Come Back.

Service Call Platinum Client- unit was not receiving call for heat due to a failed condensate pump. Replaced pump and system started running again. Changed out dirty water panel for humidifier.

Performed Platinum Comfort Club Membership Tune-Up on Heating System Cleaned and checked operation of furnace. Changed 16-25-1 filter. Recommend surge protector for equipment.

Performed Platinum Comfort Club Membership Tune-Up on Heating System - cleaned and checked operation of furnaces. Changed Aprilaire 413 filters. Drain tube from condensate pump was completely clogged up. Replaced tubing and verified it was draining properly. Found failing capacitor on blower motor on upstairs system. Recommended replacement of part to avoid any potential issues. Upstairs system: Exhaust amps .65 Blower amps 8.5 Temp rise 51 degrees O2 15.7% Efficiency 88.2% Tstk 101 degrees CO(0) 152 ppm

Service Call Fee: Arrived to find blower motor had failed. All parts for furnace are obsolete so recommended replacement of system but found a motor that was compatible with furnace. Replaced blower motor and tested operation. System is working properly at this time.

Service Call Fee: Arrived to find blower Had a completely dead cap and blower was failing. Was able to get system running for a short time but customer requested quotes due to age and condition. Gave a ballpark quote around 600-800 for repair.

Service Call Platinum Client- 30 yr old heil furnace. Unit is extremely dirty. Flame runs for about a minute before shutting off from over heating. Unit has a bunch of rust that has fallen inside from the heat exchanger. Unit is having issue from a combination of age, cleanliness, probable heat exchanger going out. Customer is getting an estimate today to replace the furnace. Estimate cost of cleaning system is around $1000-1200. Given the age of the system and likely hood of other parts failing I do not recommend any repair.

Service Call Platinum Client-old package unit from the 90’s had a locked up draft motor. Estimate repair cost $600-900. Customer has requested an appointment with a comfort advisor for an estimate for new unit. Estimate scheduled 11-1 today.

Performed Platinum Comfort Club Membership Tune-Up on Heating System: Performed the yearly checks on the furnace. All checks were good.

Performed Platinum Comfort Club Membership Tune-Up on Heating System: Performed yearly checks on the furnace. Replaced customer provided filter. Checked wiring and motor amps. Checked gas pressure and temperature rise. All checks were good. No further action needed at this time.

Service Call Platinum Client Arrived to find inducer motor beginning to fail and is grinding. Also condensate pump is locked up and isn’t pumping. System is about 20 years old and customer wants quotes on a new system.

Service Call Fee: Arrived to find gas valve not opening and fan limit failed. Recommended replacement due to system being very old and condition of the heat exchanger being unknown. Customer getting quote for new system

Performed Platinum Comfort Club Membership Tune-Up on Heating System. Performed maintenance on 2018 RUUD system. Replaced the AA413 filter and #35 water panel to customers 600 series humidifier. All checks good at this time and system is operating safely and properly.

Performed Platinum Comfort Club Membership Tune-Up on Heating System. Performed maintenance on two Arcoaire systems approx. year 2000. Filter sizes are 16x20x1 and 16x25x1. Arrived to find a run capacitor well out of range, homeowner chose to address that today. Inducer motor is rated for 2.3 amps and is running at about 2.7 to note. All other checks are good and system in running safely and properly at this time.

Performed Platinum Comfort Club Membership Tune-Up on Heating System. Performed maintenance on 1994 furnace system. Arrived to find all electrical checks good, however after running about 10 minutes seemed to go out on high limit before reaching set point on thermostat. System passed combustion analysis check and I adjusted gas pressures down from a 3.57. Explained to customer about her options, however due to age and condition of system I highly advised to prepare for future replacement. Homeowner would like to meet with a comfort advisor to explore her options.

Service Call Fee:very old furnace (1985 I believe). Replaced failed transformer. System is in rough shape and customer should plan on replacing unit. Recommended getting carbon monoxide detection.

Performed Platinum Comfort Club Membership Tune-Up on Heating System Customer upgrading to cozy plus so we can be out later this year for cooling maintenance.

Service Call Platinum Client-17 yr old package unit had a locked up inducer motor. I was able to free up the motor but it will likely fail again. Customer has had a lot of issues with this equipment throughout the years. Estimate repair cost is $600-800. Customer has back up wall heaters and has requested an estimate for a new unit. Estimate scheduled today 9-11.

ICP-HEIL INDUCED DRAFT ASSEMBLY - 1010239, Was 1094073

Performed Platinum Comfort Club Membership Tune-Up on Heating System Cleaned and checked operation of furnace. Changed Skuttle 16-25 filter. Recommend surge protector for equipment.

Performed Platinum Comfort Club Membership Tune-Up on Heating System - cleaned and checked operation of equipment. Changed Skuttle 16-25 filter. Recommend surge protector for equipment. Homeowner was not home, call to verify payment for filter.

7.5/440 CAPACITOR

Service Call Platinum Client: Arrived to find humidifier supply water shut off. I opened the supply water and verified operation. Checked appropriate humidity settings to the recommended settings in the manual. Put the setting on number 5 in the high to normal setting. Observed operation. Everything checks out good.